This article mainly introduces:

Oman hydraulic cylinder,shearing machine cylinder manufacturer,shearing machine cylinder

(Oman shearing machine cylinder,produced by Hengyu Group）

shearing machine cylinder are widely used in Oman，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed shearing machine cylinder for customers from Oman.

Introduction to shearing machine cylinder:

The shearing machine cylinder can not be used as grounding electrode to avoid electric damage to the piston rod.

What kind of process is used in the shearing machine cylinder to make high-quality shearing machine cylinder products: the body is the main component of the shearing machine cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The shearing machine cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the shearing machine cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the shearing machine cylinder increases by 25%. If the service life of the shearing machine cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. shearing machine cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the shearing machine cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and shearing machine cylinder are stuck or the shearing machine cylinder is blocked. At this time, no matter how to manipulate, the shearing machine cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the shearing machine cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

The difference between the plunger shearing machine cylinder and the piston shearing machine cylinder is that the piston in the shearing machine cylinder is replaced by a shaft plunger, which is used in hydraulic transmission requiring a long mechanical stroke, and can only input pressure oil from one direction, pressurize in a single direction, and form a thrust to push the plunger to move. The return trip of the plunger depends on the plunger itself to fall, and some rely on the spring to push back to the original position. Usually used plunger type shearing machine cylinder, its inner hole does not need mechanical finishing, as long as the plunger round grinding can be assembled.

When the shearing machine cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the shearing machine cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

Answers to some questions about shearing machine cylinder:

What are the four cylinders of the truck crane?
The four cylinders of the truck crane generally refer to the telescopic cylinder of the boom (to adjust the length of the boom), the variable amplitude cylinder of the boom (to adjust the elevation Angle of the boom), the horizontal telescopic cylinder of the support leg and the vertical cylinder of the support leg.

Why does the hydraulic cylinder ring?
1 Air intrusion into the hydraulic system is the main reason for noise 2 The relief valve is unstable, such as due to the improper combination of the slide valve and the valve hole or the contact of the cone valve and the seat is stuck by dirt, the damping hole is blocked, the spring is crooked or fails to make the spool stuck or move in the valve hole, causing system pressure fluctuation and noise. 3 Improper adjustment of the reversing valve causes the spool of the reversing valve to move too fast, resulting in reversing impact, resulting in noise and vibration. 4 Mechanical vibration, such as long tubing, elbow more and not fixed, when the oil flow through, especially when the flow rate is high, easy to cause pipe shaking; The rotating part of the motor and hydraulic pump is unbalanced, or the alignment is not good during installation, or the coupling is loose, etc., which can produce vibration and noise.