This article mainly introduces:

Cote d 'Ivoire hydraulic cylinder,reset cylinder manufacturer,reset cylinder

(Cote d 'Ivoire reset cylinder,produced by Hengyu Hydraulic Co., Ltd）

reset cylinder are widely used in Cote d 'Ivoire，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed reset cylinder for customers from Cote d 'Ivoire.

Introduction to reset cylinder:

The coordination of the sliding parts of the reset cylinder itself should not be too tight, the sealing friction force should not be too large, and H8 / f8 coordination should be selected between the piston rod and the guide sleeve; Check whether the size of the sealing ring is processed strictly according to the standard; If the V-shaped sealing ring is used, the sealing friction should be adjusted to a moderate degree.

The reset cylinder should be used correctly and maintained regularly. The reset cylinder should be deflated before use, the buffer regulating valve should be adjusted to a reasonable position, the cleanliness of the oil should be checked regularly, the dust on the reset cylinder should be cleaned regularly, and attention should be paid to waterproof and fireproof.

The wear of the hard chromium plating layer of the reset cylinder is mostly caused by the grinding of the friction iron powder of the piston, and the wear is faster when there is water in the middle. Corrosion caused by the contact potential difference of the metal only occurs in the part of the piston contact, and the corrosion occurs in a point pattern. As mentioned above, when there is moisture in the middle, it will promote the development of corrosion. Compared with castings, the contact potential difference of copper alloy is higher, so the corrosion degree of copper alloy is more serious.

reset cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a reset cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' reset cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the reset cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The reset cylinder mainly outputs linear motion and force. The reset cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston reset cylinder, plunger reset cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger reset cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

Answers to some questions about reset cylinder:

Why the injection cylinder retreating after the injection molding machine is started?
It is likely that the projected area of the molded plastic parts is large or the injection pressure set is relatively large, resulting in the expansion force exceeding the clamping force of the injection molding machine, so the mold is backward. You can do the following attempts: 1, reduce the injection force of the injection molding machine; 2, if the injection molding part can not be well formed by reducing the injection force, it is recommended to install the mold to a larger injection molding machine.

Two cylinders in parallel, how to solve the synchronization problem?
The following methods can be used to achieve parallel cylinder synchronization: 1, rigid mechanical synchronization. 2. The throttle valve or speed regulating valve is used in the circuit to adjust the synchronization. 3, the two cylinders use independent quantitative pump oil supply to achieve synchronization. 4. Synchronous motor is used in the loop to realize cylinder synchronization. 5, using the position sensor to measure the stroke position and control the cylinder synchronization through the electrical system.