This article mainly introduces:

Britain hydraulic cylinder,push and pull the cylinder manufacturer,push and pull the cylinder

(Britain push and pull the cylinder,produced by Hengyu Hydraulic Cylinder Factory）

push and pull the cylinder are widely used in Britain，because of no need for deceleration device，long service life，smooth movement.So our company has designed push and pull the cylinder for customers from Britain.

Introduction to push and pull the cylinder:

The assembly work of the push and pull the cylinder has a great impact on the quality of the push and pull the cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

push and pull the cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the push and pull the cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

push and pull the cylinder to reasonable use of hydraulic oil: strict hydraulic oil selection off. Hydraulic oil is selected in strict accordance with oil standards. The selection of good quality hydraulic oil can effectively prevent bubbles in the working process of the hydraulic system. When choosing the oil, it should be selected according to the lowest temperature in different regions, and fill the hydraulic oil according to the dipstick standard, and at the same time, it should also keep the hydraulic system clean (when filling the hydraulic oil, it should prevent the water and other impurities into it), and often check the oil quality, oil level and oil color of the hydraulic oil. If blisters and bubbles are found in the hydraulic oil. When the oil becomes milky white, the source of the air in the oil should be carefully found and eliminated in time.

Most of the failure of the push and pull the cylinder is because there is a foreign body in the push and pull the cylinder into the failure of the push and pull the cylinder, the most problematic is that it is difficult to determine when the foreign body is into the push and pull the cylinder. After a foreign body enters, if the outer side of the sliding surface of the piston is equipped with a seal with a lip edge, then the lip edge of the seal can scrape the foreign body when working, which is beneficial to avoid scratching. However, the piston equipped with 0-shaped sealing ring has a sliding surface at both ends, and foreign bodies are sandwiched between this sliding surface, which is easy to form scars.

Answers to some questions about push and pull the cylinder:

Is it good or bad for the hydraulic cylinder working in the limit stroke position?
It is not good for the hydraulic cylinder working in the limit stroke position. Generally, when the cylinder is used in the limit stroke, the oil in the cylinder will form a backflow back pressure impact on the piston and guide sleeve seals. If the limit is not accurate, it is easy to cause collision damage. It is recommended to leave a buffer of ten to twenty centimeters.

How to select swing cylinder? Under what conditions are they designed and selected?
1, determine the system parameters: ① the weight and the required force; ② Nominal working pressure and range; ③ The time required to travel this distance; 4 oil medium 2, installation method: select the appropriate way for the specific application 3, cylinder diameter and working pressure: determine the cylinder diameter and provide the necessary force required by the system pressure 4, piston rod: determine the minimum piston rod diameter required to withstand the longitudinal bending force, select the appropriate piston rod end and piston rod end thread 5, piston: Whether the seal type is suitable for the application 6, buffer: choose the buffer requirements as appropriate.