This article mainly introduces:

Nigeria hydraulic cylinder,spring return cylinder manufacturer,spring return cylinder

(Nigeria spring return cylinder,produced by Hengyu Hydraulic Co., Ltd）

spring return cylinder are widely used in Nigeria，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed spring return cylinder for customers from Nigeria.

Introduction to spring return cylinder:

If the spring return cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the spring return cylinder. The internal parts of the spring return cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the spring return cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the spring return cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the spring return cylinder bore processing is out of whack. Because the piston and spring return cylinder, guide rail and piston rod are relative If the spring return cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling spring return cylinder weight composition and calculation. The weight of the spring return cylinder is composed of the spring return cylinder diameter, the outer diameter and weight of the spring return cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

spring return cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the spring return cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

When the spring return cylinder is installed on the main engine, the oil port piping part and the guide sleeve should be checked for oil leakage in the running test, and the earring and the middle hinge shaft bearing should be refueled.

The internal leakage of the spring return cylinder should be prevented when the spring return cylinder is used. The internal leakage of spring return cylinder includes the leakage caused by excessive wear of spring return cylinder block seal, piston rod and seal cover seal and piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time.

Answers to some questions about spring return cylinder:

How does the self-locking cylinder work?
Hydraulic cylinder self-locking is divided into oil self-locking and mechanical self-locking. The oil circuit itself is equipped with a valve to maintain pressure, so that the hydraulic oil of the cylinder does not return to the tank, and the oil chamber of the cylinder is filled with a certain pressure of oil. However, this pressure holding self-locking is not very safe and reliable, and the plunger will slowly return if there is a leak. Mechanical self-locking is to install a nut on the plunger of the cylinder, and when the cylinder rises to the required position, the nut on the cylinder plunger is rotated to the end, and the cylinder block is in contact, so that the plunger will be fixed to the required height. When it is necessary to relieve the pressure, screw the nut on again and let the plunger return to the position. This kind of cylinder has a special name, called self-locking hydraulic cylinder.

How does the one-way solenoid valve control the hydraulic cylinder circuit?
If your cylinder is single-acting, you can use a one-way solenoid valve, such as some lifting platform hydraulic cylinder, the support valve used is one-way (two-position tee), that is, the cylinder extends out by the oil pressure top, the cylinder retracted by its own weight.