This article mainly introduces:
Japan hydraulic cylinder,swager cylinder manufacturer,swager cylinder
(Japan swager cylinder,produced by Hengyu Hydraulic Co., Ltd）
swager cylinder are widely used in Japan，because of long service life，smooth movement，high work efficiency.So our company has designed swager cylinder for customers from Japan.
The material of the sliding part of the swager cylinder piston sintered casting piston will cause sintering phenomenon when subjected to large transverse load. In this case, the sliding part of the piston should be made of copper alloy or welded to such material.
swager cylinder and hydraulic station selection: Select the type and structure of the swager cylinder according to the operation requirements of the main engine. According to the external load force borne by the swager cylinder, such as gravity, friction force of the external mechanism, inertia force and working load, determine the load change law of the swager cylinder in each stage of the stroke and the power value that must be provided. Determine the diameter of the piston and piston rod according to the working load of the swager cylinder and the selected oil working pressure. the flow rate of the hydraulic pump is determined according to the movement speed of the swager cylinder, the diameter of the piston and the piston rod.
The piston rod of the swager cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.
If the swager cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the swager cylinder. The internal parts of the swager cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the swager cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the swager cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the swager cylinder bore processing is out of whack. Because the piston and swager cylinder, guide rail and piston rod are relative If the swager cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling swager cylinder weight composition and calculation. The weight of the swager cylinder is composed of the swager cylinder diameter, the outer diameter and weight of the swager cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.
What type of seal is the cylinder of shaft 50?
You won't know the exact model until you take it apart. Oil seals have O, Y, Yx, KYx, U, UN, UHS, YA, St, Gray, Yamagata, Lei type, etc. It is difficult to know what kind of oil seal the designer chooses. Cylinder oil seal installation method: 1. Receive a fixed number of oil seals. 2. From receiving the oil seal to assembly, it must be kept clean. 3. Before assembly, check the oil seal and measure whether the size of each part of the oil seal is consistent with the size of the shaft and cavity. Before the oil seal is installed, the size of the shaft diameter should be clearly compared with the inner diameter of the oil seal. The inner cavity size should be suitable for the outer diameter width of the oil seal. Check the lip of the oil seal for damage.
What is a two-way hydraulic cylinder?
Bidirectional hydraulic cylinder definition: The bidirectional hydraulic cylinder uses the oil as the working medium, transmits the movement through the change of the sealing volume, and transmits the power through the pressure inside the oil. The two-way cylinder has at least two oil ports, which are used to connect the hydraulic tubing, and control the extension and retraction of the cylinder by pressing.
Add Wechat