This article mainly introduces:

Croatia hydraulic cylinder,disc spring hydraulic cylinder manufacturer,disc spring hydraulic cylinder

(Croatia disc spring hydraulic cylinder,produced by Hengyu Group）

disc spring hydraulic cylinder are widely used in Croatia，because of no transmission clearance，long service life，smooth movement.So our company has designed disc spring hydraulic cylinder for customers from Croatia.

Introduction to disc spring hydraulic cylinder:

The repair method of disc spring hydraulic cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

disc spring hydraulic cylinder piston rod material selection and requirements: ① piston rod is usually made of 45 steel. When there is a large impact force and heavy load transmission, it is made of 40Cr steel. This is to ensure that the piston rod has sufficient working strength. The piston rod is generally designed as a disc spring hydraulic cylinder, if the diameter is larger, the hollow piston rod can be used. Made of No. 45 seamless steel pipe. ③ When the piston rod is manufactured, the blank should be first forged and conditioned after mechanical rough processing, and the hardness of HB=230 ~ 250. The purpose of conditioning is to improve the machining performance and increase the working strength of the material. ④ The surface roughness Ra of the piston rod after finishing should not be greater than 0.65μm. ⑤ In order to improve the corrosion resistance of the piston rod, the working surface of the rod can be plated with hard chromium. ⑥ The piston rod and the end cap are guided by H8 ' disc spring hydraulic cylinder piston rod industry standard: piston rod diameter series of national recommended standard GB/T2348-1993. Piston rod thread size series standard GB/T2350-1980. Please refer to execute. There is no industry standard for piston rods Both the disc spring hydraulic cylinder and the hydraulic motor are devices that convert the pressure energy of the liquid into mechanical energy and output it. The disc spring hydraulic cylinder mainly outputs linear motion and force. The disc spring hydraulic cylinder has a variety of forms, according to the different characteristics of its mechanism it can be divided into piston type, plunger type and swing type three categories, according to the mode of action he can be divided into single action and double action. Piston disc spring hydraulic cylinder, plunger disc spring hydraulic cylinder is mainly used for: machinery, such as excavators; Scientific research, such as university structure laboratory. The plunger disc spring hydraulic cylinder is used for pressure testing machines, such as Jinan test, and the test machine is used for material testing.

When the hydraulic oil is not pumped into the disc spring hydraulic cylinder, it is necessary to check whether the tubing, oil circuit, especially the hose joint has been blocked, and the relevant oil circuit from the disc spring hydraulic cylinder to the pump should be checked in turn and blocked; Check whether the seal between the taper valve and the seat of the relief valve is good; Check whether the solenoid valve spring is damaged or whether the solenoid coil is burned out; Whether the oil circuit is switched is insensitive.

The disc spring hydraulic cylinder is not the same as the disc spring hydraulic cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the disc spring hydraulic cylinder can not be used as a high-power power component, but the disc spring hydraulic cylinder can be used as a relatively large power component, or the disc spring hydraulic cylinder system can be used.

Answers to some questions about disc spring hydraulic cylinder:

How to produce good quality hydraulic cylinder?
According to the principle of quality control, it is considered from five aspects: people, machine, material, method and environment. 1, People, refers to the processing and assembly operators. Their skills, professional qualifications, literacy should meet the requirements of production. For example, do your machining workers have the required grade certificate? Do your welders have welding certificate? 2, Machine, refers to your production equipment. Production cylinders have requirements for processing equipment. For example, the piston rod requires chrome grinding. Can your equipment meet the need? 3, Material. The material you use should meet the quality requirements. For example, the sealing ring of PARK and domestic goods is different. Material is also very important. 4. Method refers to the process method. Do your processing and assembly processes meet the requirements? 5, Environment. The environment shall be neat and orderly, clean and hygienic. It is especially important for the hydraulic cylinder production enterprise environment. Can your assembly shop site be clean and dust-free? Quality inspection is also a focus of control. Products should do pressure test, leakage test. The test pressure should reach 1.25 times the design pressure. If you can't maintain pressure, what about quality? You may not be able to do the whole process of cylinder production, you can take the method of OEM. Taking advantage of the strengths of specialized manufacturers, you contract out what you need and then assemble it yourself. But the principle of quality control is the same.

What components can control cylinder rising and falling speed and the speed is adjustable?
A throttle or special solenoid valve is required. The reversing valve can choose the three-position reversing valve with P-type middle function. When rising, the reversing valve can be changed to the middle position to achieve differential connection and the fastest speed. Add a combination valve one-way throttle valve in the oil return circuit, connection mode: when the cylinder rises, the oil flows back to the tank through the check valve, the throttle valve is reversed off, when the cylinder falls, the reversing valve is changed to the left or right position (see the structure of the valve), the check valve is reversed off, the oil returns to the tank through the throttle valve, and the speed can be adjusted through the throttle valve.