This article mainly introduces:

Turkmenistan hydraulic cylinder,trunnion cylinder manufacturer,trunnion cylinder

(Turkmenistan trunnion cylinder,produced by Hengyu Group）

trunnion cylinder are widely used in Turkmenistan，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed trunnion cylinder for customers from Turkmenistan.

Introduction to trunnion cylinder:

When the trunnion cylinder is installed, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the trunnion cylinder head, earring (or middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent rigid interference and cause unnecessary damage.

1, the hydraulic machinery should be kept clean, in order to prevent dust and debris from falling into the oil, the tank should be sealed. 2, the oil in the tank should be replaced regularly according to the working condition. When changing the oil, the dirt and impurities accumulated at the bottom of the tank should be removed and the tank should be cleaned. 3, hydraulic oil, oil drums should be set in a clean and safe place to strengthen management. The oil drum, oil filter, oil funnel, oil pipe, etc. used should be kept clean. The oil drums for loading hydraulic oil must be cleaned in advance, and the oil drums should be dedicated and not mixed with other oil drums.

How to determine the working pressure of the trunnion cylinder: The pressure depends on the load size (i.e., F) and the type of equipment. The limitations of assembly space, economic conditions and component availability of the actuator should also be considered. In the case of a certain load, it is necessary to increase the structural size of the actuator if the working pressure is low, for some equipment, the size may be limited, and it is not economical from the point of view of material consumption; On the contrary, if the pressure selection is too high, the material, sealing and manufacturing accuracy of the pump, trunnion cylinder, valve and other components are also required to be high, which will inevitably increase the cost of equipment. In general, for equipment with a fixed size that is not too limited, the pressure can be selected lower, and the walking machinery should be selected higher.

When the trunnion cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the trunnion cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the trunnion cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the trunnion cylinder can meet the requirements by grinding. However, the life and reliability of this repair trunnion cylinder are not high.

Answers to some questions about trunnion cylinder:

How to deal with the surface degreasing process before spraying paint after cylinder assembly, and what degreasing agent is used?
Cylinder painting, generally using the following process (note: the cylinder is best painted, do not spray powder coating, because the powder coating curing temperature is high, will lead to sealing defects and oil leakage) : Pre-degreasing - degreasing - washing - washing - pickling - washing - washing - table adjustment - phosphating - washing - washing - drying - polishing - spray primer - spray paint degreasing agent generally use neutral or weak alkaline degreasing agent, phosphating liquid generally use zinc phosphating liquid.

What size of hydraulic cylinder is needed for 200 tons pressure? The pressure of the cylinder at work is determined by the load, and the pressure of the physical force is equal to the force divided by the area of action (that is, P=F/S). If you want to calculate the output force of the cylinder, you can calculate by the formula: Set the radius of the piston (that is, the cylinder) is R (unit mm) the radius of the piston rod is r (unit mm) the pressure level P (unit MPa) when working, then the thrust of the cylinder F push =3.14*R*R*P (unit N) the pull of the cylinder F pull =3.14* (R* R-R *R) *P (unit N) 100 tons of the cylinder, System pressure 16Mpa.