This article mainly introduces:

Colombia hydraulic cylinder,stainless steel cylinder manufacturer,stainless steel cylinder

(Colombia stainless steel cylinder,produced by Hebei Hengyu company）

stainless steel cylinder are widely used in Colombia，because of no transmission clearance，simple structure and reliable operation，excellent temperature resistance.So our company has designed stainless steel cylinder for customers from Colombia.

Introduction to stainless steel cylinder:

The cavitation of the stainless steel cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the stainless steel cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

stainless steel cylinder piston rod material selection and technical requirements: (I), because there is no special requirements, so use 45 steel as the piston rod material, the design of the piston rod only withstand pressure stress, so no modulation processing; (ii) The coaxial tolerance of the shaft journal and the outer circle of the mounting piston is not greater than 0.01mm, so as to ensure the coaxial degree of the outer circle of the piston rod and the outer circle of the piston, and avoid the stuck phenomenon of the piston and the stainless steel cylinder, the piston rod and the guide. The vertical tolerance between the end face of the mounting piston and the axis of the piston rod is not more than 0.04mm/100mm to ensure that the piston installation does not produce skew; (iii) The outer circle of the piston rod should pay attention to the roughness; (iv) Because it is operated under low load conditions, surface treatment is omitted.

stainless steel cylinders in series, parallel and series parallel. Series: In the stainless steel cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Series: In the stainless steel cylinder, the oil inlet of the subsequent reversing valve is the supply of the previous oil return, and there is no separate oil return circuit connected with the oil return in each valve. Parallel: the pressure oil in the stainless steel cylinder is connected with the inlet oil of each reversing valve, and the return oil is collected by the return oil circuit. Series parallel: For this one, compared with the simple series and parallel, it is slightly more complicated, but it is not impossible to understand. The series refers to the oil in the stainless steel cylinder, which is in series form, but can not form a series circuit, and the parallel refers to the oil return circuit of each valve, which is in parallel.

The piston seal of the stainless steel cylinder is the main element to prevent leakage in the stainless steel cylinder. For the lip seal, it should focus on checking whether the lip edge is bruised and worn, and for the combination seal, it should focus on checking the wear of the sealing surface, and then determine whether the seal can be used. In addition, it is necessary to check whether the static seal between the piston and the piston rod is crushed. The piston rod seal should focus on checking the wear of the seals and supporting rings.

Answers to some questions about stainless steel cylinder:

What is the bearing capacity of the HOB cylinder?
The normal specification of HOB is 140 kg pressure, which is more commonly used in the market, and there are clear marks on the cylinder, 210 kg is a strengthened version of HOB, generally customized cylinders are also clearly marked on the above, when the specific use of the cylinder, the maximum use pressure is marked on the cylinder.

Hydraulic cylinder performance requirements?
Hydraulic cylinder performance requirements: hydraulic cylinder is the hydraulic system to achieve energy transfer, conversion and control of the working medium, in addition, it is also responsible for the lubrication of the system, rust prevention, corrosion prevention and cooling. The performance of hydraulic oil will make the system flexible, accurate and reliable. Hydraulic performance requirements are determined according to the design parameters of the hydraulic system, operating conditions, the structure of the hydraulic pump and the working environment. Appropriate viscosity and good viscosion-temperature performance Viscosity is an important performance indicator of hydraulic pressure, which has an important impact on the smooth operation of the hydraulic system and the friction parts. The low temperature performance of hydraulic oil includes three aspects: low temperature flow, low temperature start-up and low temperature pumping.